【School】 escalator walkways weak test items and test methods --- Power By 【China】 weak home network.

<br> test | serial number | Test content and requirements | Test Method | <BR> | Projects | | | | <BR> |--|--|--------------- .-----|---------|< BR> | | | (1) product certification; | Search | <BR> | | | (2) approved by the department of labor to install, repair, change .| | <BR> | | | made for examination and approval materials; | | <BR> | | | (3) safety inspection reports and corporate self-reporting | | <BR> | Technology | | REPORT; | | <BR> .| | | (4) installation, commissioning, operation, maintenance instructions; | | <BR> | operation | | (5) installation and acceptance (including the Department of Civil Engineering | | <BR> | | 1 | pm); | | <BR .> | file | | (6) equipment, general layout, electrical schematics and wiring | | <BR> | | | map; | | <BR> | case | | (7) repair, alteration, maintenance, service, self-test and .| | <BR> | | | test records; | | <BR> | | | (8) personal, equipment, accident records; | | <BR> | | | equipment management archiving, security management | | <BR> | | .| department is responsible for implementation. .| | <BR> |--|--|--------------------|---------|< BR> | Regulations | | .establish and implement a system of at least the following: | Search | <BR> | chapter | 2 | (1) shift relief system; | | <BR> | System | | (2) safe operation; (3) repair and maintenance | | < .BR> | ° | | system. .| | <BR> |--|--|--------------------|---------|< BR> | | | In addition to .vents, with a step or pedal operation, Rotary | Visual inspection | <BR> | closed | 3 | Hand device application of non-porous materials outside the equipment sealed | | <BR> | | | closed. .| | <BR> <BR> |--|--|--------------------|---------|< BR> | .| | import and export in width should be provided at the small | | <BR> | the area | | in the escalator width, length not less than 2.5m of the | |<BR> | into | 4 | Non-restricted area, when the width of the .more than the width of the escalator | with tape measure | <BR> | port domain | | 2 times, the length can be reduced to 2m, escalators | | <BR> | | | clearance height of not less than 2.3m. .| | <BR> |--|--|--------------------|---------|< BR> | | 5 | .should remind passengers near the entrance handrails help | Visual inspection | <BR> | Standard Ming | | standing symbol of the words. .| | <BR> | Blog |--|--------------------|---------|< BR> | and licensing | 6. | site should be in the apparent manufacturer nameplate, nameplate | Visual inspection | <BR> | | | should be the name of manufacturer, model, and so forth. .| | <BR> |--|--|--------------------|---------|< BR> | | 7 | .room should be kept clean and free of debris, oil, and the | Visual inspection | <BR> | | | It has nothing to do with the equipment items. .| | <BR> | |--|--------------------|---------|< BR> | Machine | 8 | Room .entrance door and check the door should lock, lock only | Visual inspection | <BR> | | | can use a key or special tools to open. .| | <BR> | |--|--------------------|---------|< BR> | | | (1) .drive should be an area of the engine room engine room and return | | <BR> | | | 2 | | <BR> | Housing | | is not less than 0.3m, the length of the short side is not less than | | <BR> | | | 0.5m .standing space. .| | <BR> | | | (2) control box should be provided not less than the previous | | <BR> | | 9 | control box width (not less than 0.5m), vertical | tape measure | <BR> | .| | is not less than 0.7m space. .| | <BR> | | | (3) need to run maintenance and inspection of components to | | <BR> | | | 2 | | <BR> | | | party shall provide not less than 0.5 × 0.6m of .empty | | <BR> | | | room. .| | <BR> |--|--|--------------------|---------|< BR> | | 10 | .two consecutive steps or the space between the pedals | feeler gauge measurement | <BR> | | | should not exceed 6mm. .| | <BR> | |--|--------------------|---------|< BR> | | | step or pedal .and the apron of the gap, each side does not | | <BR> | ladder | 11 | should be more than 4mm, both sides of the gap of and should not be overloaded | feeler gauge measurement | <BR> | Level | | over 7mm. .| | <BR> | Or |--|--------------------|---------|< BR> | step | 12 | .in the horizontal section, the two adjacent steps of the high degree of | caliper or depth gauge measurement | <BR> | Board | | difference should be not more than 4mm. .| | <BR> | |--|--------------------|---------|< BR> | | | | visual, .to move the body center of gravity | <BR> | | | | check step or pedal | <BR> | | | steps damage or not pedal surface, fixed to be | the direction of the swing amount, | <BR> | | 13 | good .in the horizontal direction and should not be run over | body against the handrails | <BR> | | | amount of swimming. .| Check the feet to promote the cascade | <BR> | | | | stairs or pedal horizontal shift | <BR> | | | | momentum. .| <BR> |--|--|--------------------|---------|< BR> | | | | use .measuring tape from the comb | <BR> | | 14 | escalator steps at the entrance should be in the water | board out of the Cascade front | <BR> | | | ping-oriented segment, its length is not less than 0.8m. .| And the cascade trailing edge to comb | <BR> | | | | the distance between the plates. .| <BR> |--|--|--------------------|---------|< BR> | | | comb .board should not be damaged. .Meshing comb and cascade | | <BR> | comb | 15 | to be good, engaging depth of not less than 6mm, | visually, with a ruler measuring | <BR> | Board | | stairs or pedal surface to comb slots .root | | <BR> | | | vertical distance of not more than 4mm. .| | <BR> |--|--|--------------------|---------|< BR> | | | Handrail .rail or bracket with and between handrails should | | <BR> | | 16 | to avoid the possibility of the hand grip and scraping, handrails | visual, and ruler measurement | <BR> | | | with the opening and guide .distance between the rails or brackets | | <BR> | | | off should not exceed 8mm. .| | <BR> | |--|--------------------|---------|< BR> | | 17 | handrails .lateral distance between the wall | tape measure | <BR> | | | should be less than 80mm. .| | <BR> | |--|--------------------|---------|< BR> | Rotary | | at the entrance .handrail at the level of part of a long | | <BR> | | 18 | degrees, counting from the root of the comb plate is not less than | tape measure | <BR> | hand | | 0.30m. .| | <BR> | |--|--------------------|---------|< BR> | with the | 19 | Handrail .with the distance between the center lines should not be over | tape measure | <BR> | | | the distance between the apron 0.45m. .| | <BR> | |--|--------------------|---------|< BR> | | | handrail distance .vertical distance between steps pedal | | <BR> | | 20 | should not be less than 0.90m, and not greater than | tape measure | <BR> | | | 1.10m. .| | <BR> | |--|--------------------|---------|< BR> | | | turn handrail .side between the entrance and the floor | | <BR> | | 21 | vertical distance shall be not less than 0.10m. .Without large | tape measure | <BR> | | | at 0.25m. .| | <BR> |--|--|--------------------|---------|< BR> | | | Apron .board installation should be smooth, there should not be | | <BR> | Wai | 22 | hole, moldings and so on. .The joints should be butt, seam | Visual inspection | <BR> | | | should be smooth, and should have sufficient rigidity. .| | <BR> | Skirt |--|--------------------|---------|< BR> | | | Apron board .cover line on the edge or the Department of steps,| | <BR> | board | 23 | vertical distance between the pedal should not be less than the | tape measure | <BR> | | | 25mm. .| | <BR> |--|--|--------------------|---------|< BR> | | | direction .cascade, the pedal (or tape) side of Rotary | | <BR> | | | hand equipment parts should be smooth, the pressure or the set | | <BR> | | 24 | bar direction and the direction of the installation is inconsistent | visual .Check, if necessary, with | <BR> | | | when the protruding height should not exceed 3mm, side | caliper | <BR> | help | | margin should be sturdy and have rounded or chamfered. .Any | | <BR> | hand | | hook parts should not be linked to the possibility of the object. .| | <BR> | Loaded |--|--------------------|---------|< BR> | Home | | two .the gap between the baseboard should not exceed | | <BR> | | 25 | 4mm, its edges should be rounded or chamfered. .When | feeler gauge measurement | <BR> | | | used when a single layer of shatterproof glass, security.