Weak current College】 【installed electric curtains motor and track steps --- Power By】 【China power house network.

<br> <br> First step: draw line location, measured rail dimensions <br> <br> 1. draw line positioning accuracy is installed curtain track key, first measure good fixed pitch, and the desired dimensions of the installation of the orbit .; <br> <br> 2. the customer's size should be measured as the total length of the track; <br> <br> 3. track overall length as the main gear box (motor), track length, gear box. < .br> <br> 4. curved track, may, in accordance with building radians bend arc type curtain rail. (Note: radian shall not be less than 120 °) <br> <br> About arc type curtain track measurement methods: < .br> <br> 1. arc type road Press picture, and indicate "A" and "B" and "C" length and angle of the arc-shaped rail, and indicate the location of the main transmission gearbox, single-drive or .dual-drive (Note: the "A" and "B" length contains main gearbox and Deputy transmission box length. <br> <br> 2. for viewing platform, the radial road, by drawing out and indicate (chord), ( .ARC), (ARC). And indicate the location of the main transmission gearbox. Single-drive or dual-drive, the size is the track or external dimension in the dimension. (Note: the arc length contains main gearbox and Deputy transmission box .length) <br> <br> Step 2: installing lifting clamp <br> <br> Will clamp rotated 90 ° and rail links, with self-tapping screws lifting clamp installed on the roof (like a concrete structure, needed to be expansive .products to be silk. <br> <br> Step three: curtains motor wiring <br> <br> (Note: two-machine connection please refer to product specifications) <br> <br> Step four: curtains motor and rail join .<br> <br> Specialized complex motor using crawler curtain track ends fitted with gearbox, and motor-gear box is connected to the other end as Deputy gearbox. Specific actions are as follows: <br> <br> 1. put the power .of 90 ° to the master gear box; (Note: the main gearbox of the flat rotation axis and motor interface to match) <br> <br> 2. the motor rotates 90 ° clockwise; <br> <br> 3. rotating .in place, the plate is pushed into the gearbox to the limit position, will be automatically locked, motor and gearbox connection OK; finished edge connection. (Note: missed good may not power up, so as not to damage the motor) <br .> <br> Step five: curtains motor stroke adjustment <br> <br> Motor trailer is equipped with a micro switch gear and equipment, motor wiring requirements for forward and reverse, thereby achieving the curtains open and closed stroke self positioning. Stroke setting .as follows: <br> <br> 1. adjust the stroke before the curtain motor and gear box separation of the track, so that the orbit of fall is in the full open and full closed end. To remove the rear cover of electric motor ., you can see about two knobs; <br> <br> 2. knob (1) and (2) there is a locking plate, locking piece dial to the knob (2), the knob (1) push, from transparent shell .you can see the gear from the tooth and status, at which point the fingers rotate knob (1) both the forward and reverse rotation 【allows three slot (the middle one for color ring) slot for a line, you can hear the micro switch ."sentries", you can also see the micro switch produces action (corresponding micro switch into short circuit condition), the knob (1) and gently pull out (do not turn), the gear into the mating status, knob (1) adjustment .will come to a close; <br> <br> 3. then adjust knob (2), so the position lock piece dial to knob (1), and push knob (2) to state the gear from the mating,, repeated knob .(1) all resizing action, so the position micro switch into short circuit status; <br> <br> 4. will the curtains motor mounted on the rail of the transmission case, push the latch plate fixed gear box. Powered by the controller .switches for electrical power, the lock piece dial to knob (1); the knob (2) push and slightly forward and reverse rotation are 【back to knob (2); curtains for opening or closing movement, to achieve the required location, they .immediately cut off the power to the motor, gently pull the application button (2), bringing the gear into the position of teeth in-; <br> <br> 5. through the controller switches the motor operation operated directional control, so that .the lock piece to the knob (2) the knob (1) push and slightly forward and direction can be 【immediately cut off the power to the motor, gently pull out the knob (1), the gear into the position of teeth in- .; <br> <br> 6. knob (1) and (2) are tooth-transmission status, adjust the work will come to a close; <br> <br> 7. products to be used for the back cover and tighten .the screws, locking plate is fixed. <br> <br> <br>.